CO Oxidation Application Scenarios: Sintering, Incineration and Beyond
Part of the CO Oxidation: The Complete Guide — this article is one of the detailed pages in the guide.
Direct answer: CO oxidation catalysts appear wherever CO must be removed from oxygen-containing gas below the temperature where thermal oxidation is economical. The four largest scenarios are sintering machine exhaust, waste incineration, industrial furnace and kiln off-gas, and catalytic combustion tail gas — each with distinct gas compositions and therefore distinct catalyst requirements.
Sintering and pelletizing exhaust
Sintering lines emit large flows at moderate temperature (typically 120–200°C in the duct after the ESP, subject to site conditions) with CO in the thousands of ppm range, plus SO₂, moisture and residual dust.
- CO concentrations are high enough that reaction exotherm matters for reactor design.
- SO₂ and moisture are the main activity threats.
- Flow rates are enormous — pressure drop per metre of catalyst bed is a first-order economic parameter.
- Many plants combine CO oxidation with SCR or desulfurization in series, so the CO unit must tolerate upstream variability.
Waste and medical waste incineration
Incineration flue gas carries CO spikes that reflect incomplete combustion events — the CO level itself is a combustion-quality signal.
- Duty is highly dynamic: CO swings with batch charging.
- HCl, SO₂, heavy metals and moisture are all present; the catalyst sits behind appropriate gas cleaning.
- Temperature is usually sufficient for light-off once the boiler design provides it; reheating may be needed at low load.
Medical waste incineration — deeper look
Medical waste units combine the worst of thermal cycling with an aggressive gas chemistry.
- Temperature: after gas cleaning the stream is often 150–220°C — near the light-off margin, so pre-heating or a low-light-off formulation is usually needed.
- CO fluctuation: batch charging produces surges from the hundreds to the thousands of mg/Nm³; size for the peak and verify the exotherm stays safe.
- Poisons: residual HCl after the scrubber and heavy-metal fume attack the catalyst; chloride tolerance and upstream cleaning define the catalyst life.
- Sizing note: the documented medical-waste result in the Evidence Registry (XB-EV-002) shows high single-pass conversion, but the test record does not publish flow, temperature or O₂ — so the duty must be re-sized on the customer's own measured gas, not copied from the result.
Industrial furnaces, kilns and dryers
Furnaces, rotary kilns and drying lines vent CO from incomplete fuel burnout.
- Streams are smaller and often intermittent.
- Temperature varies with batch operation — light-off margin and pre-heating matter.
- Where fuel is switched seasonally, gas composition shifts; sizing should cover the worst-case fuel.
Gas-fired boilers and kilns — deeper look
Gas-fired units run cleaner than coal or incineration but have their own CO pattern.
- Temperature: gas burners hold flue-gas temperature relatively stable, but low-load and start-up conditions can fall below light-off.
- CO fluctuation: CO tracks air-fuel ratio upsets — a briefly rich burner can spike CO sharply; a polishing catalyst must ride these transients.
- Poisons: low SO₂ and dust on natural gas means longer catalyst life, but moisture from combustion is always present; condensation protection still matters.
- Sizing note: the sizing input is the peak CO during burner upsets, not the steady-state average, because compliance can be tested during a transient.
Coking flue gas
Coke-oven and coking by-product gas streams add complexity beyond a simple furnace vent.
- Temperature: coking flue gas temperature varies with the battery operating cycle and heat-recovery design; confirm the minimum continuous temperature at the catalyst face.
- CO fluctuation: CO level shifts with oven charging and pushing; treat as a dynamic duty, not a steady stream.
- Poisons: coking gas can carry sulfur species (H₂S, SO₂), tars and condensables that foul or poison the catalyst — upstream tar removal and sulfur control are prerequisites.
- Sizing note: a coking stream is sized like a sintering stream in miniature — poisons and duty pattern dominate, and the catalyst must sit behind effective particulate and tar removal.
Catalytic combustion tail gas
Catalytic combustion units can emit small residual CO at low temperature. A polishing CO catalyst downstream guarantees compliance across operating conditions.
Enclosed-space and emergency duty
In enclosed environments (garages, tunnels, industrial halls) CO removal is a safety function rather than an emissions function. Heating-tube catalyst systems with electric pre-heating provide continuous low-temperature CO abatement.
Sizing by scenario
| Scenario | Temperature | Key challenges |
|---|---|---|
| Sintering exhaust | Moderate | SO₂, moisture, huge flow |
| Medical waste incineration | Variable, near light-off | HCl, metals, dynamic load |
| Gas boiler / kiln | Stable | Cold starts, burner-transient CO |
| Coking flue gas | Variable | Sulfur, tars, duty swings |
| Furnace / kiln off-gas | Intermittent | Cold starts, fuel changes |
| Catalytic combustion tail | Low | Low-temperature light-off |
| Enclosed space | Ambient | Continuous safety duty |
Documented field results
Two scenarios have documented field-test evidence, registered in the Evidence Registry:
- Sintering machine CO (XB-EV-001): CO 1,499 ppm → 18 ppm (2022-08-23) — see Sintering Machine CO Control.
- Medical waste incinerator CO (XB-EV-002): CO 11,224.2 mg/Nm³ → 16.2 mg/Nm³ (2023-03-20) — see Waste Incineration CO Control.
Both are Field Test Results and Partially recorded — the operating conditions behind the numbers are not published, so neither result generalizes to other plants. The coking and gas-boiler scenarios have no published field evidence and are described above from engineering principles only.
Manufacturer perspective
Scenario dictates the guardrails, not the catalyst chemistry alone. We size from the actual stream data per unit — temperature profile, CO range, moisture, SO₂ and duty pattern — because the same CO removal target leads to different designs in each scenario.
Related articles
← Back to the CO Oxidation: The Complete Guide